Perle-systems 1700 Manual do Utilizador Página 11
- Página / 100
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
Applications
5
Power Up the Bridge/Router
Once the LAN and Link connections are made and the console is connected to a terminal,
you are ready to power-up the router. Connect the AC power cord to the back of the router
and plug the cord into the AC wall outlet.
Observe the LEDs as the bridge/router powers up. The LEDs will go through a circular
flashing pattern as the power-up diagnostics are performed. After the power-up diagnostics
are finished, the Power LED will go from red to green.
Enter at least one <RETURN> (up to three if necessary) in order for the bridge/router to
determine the baud rate of the terminal used for the console (i.e., autobaud). The following
information will now be seen on the console connected to the bridge/router :
Terminals supported:
ansi, avt, ibm3101, qvt109, qvt102, qvt119, tvi925,
tvi950, vt52, vt100, wyse-50, wyse-vp, teletype
Enter terminal type:
Select the terminal type being used if listed and enter its name (in lower case) at the prompt,
or choose the terminal type teletype if your terminal is not listed. This terminal type
operates in scroll mode and may be used successfully until a custom terminal definition is
created.
Managing the P1705 & P1730
Using the Menus
This section describes the minimum configuration parameters required when setting up the
P1705 & P1730. Each of the configuration scenarios requires setting of operational
parameters on the P1705 & P1730. The built-in menu system of the P1705 & P1730 is used
to configure the unit.
The router menu system operates on a “hotkey” principle; navigating around the menu
system is done by typing the number associated with the desired option; the P1705 & P1730
acts on the choice immediately (no need to hit the “enter” key).
The menu system consists of different menu levels each containing new configuration options.
Navigation back out of a nested menu is easily accomplished by pressing the tab key. The tab
key takes you to the previous menu level. If you wish to move from your current menu
location directly to the main menu simply press the equals “=” key.
When choosing menu options that will toggle between values, simply pressing the number
associated with that option will cause the options value to change. Each successive selection
of the option will cause the option’s value to change again.
Some menu options require input from the operator. When selecting an option that
requires a value, the menu system will display the range of values acceptable and a prompt
symbol “>”. Enter the new value at the prompt symbol and press enter. Should you make
an error in entering the new value, the <BACKSPACE> key (for most terminals) deletes the
most recently entered characters.
- Bridge / Routers 1
- User And System 1
- Administration Guide 1
- Using This Manual 3
- Contents 4
- Installation 7
- Identify the Reset Switch 8
- Identify the Connectors 9
- Connect to the Console 10
- Make the Link Connection(s) 10
- Power Up the Bridge/Router 11
- Using the Menus 11
- Sub-Menu Name 12
- Option Name 12
- Configuration 13
- (T1/E1 WAN only) 14
- Set Link Interface Type: 15
- Mandatory Configuration 16
- LINK 1/LAN 2 17
- Bridging and Routing 19
- Should You Bridge or Route? 19
- WAN connection 20
- Network #1 Network #2 20
- IP Routing 21
- ª Configuration 21
- ª LAN Set-up 21
- ª LAN IP Set-up 21
- IP Addressing 22
- IP Subnets 23
- ª LAN Set up 24
- ª LAN IP Set up 24
- IP Default Gateway 25
- IP Static Route 25
- IPX Routing 26
- IPX Routing Disabled 28
- IPX Frame Types 28
- IPX Routing Enabled 28
- Novell Server with Dual LANs 29
- PPP Link Configuration 30
- Numbered Links 30
- Unnumbered Links 31
- Multilink Operation 32
- Basic WAN Configurations 33
- Soft Reset 35
- Manual Call 37
- IP Address 37
- IP Address / mask size 41
- ª WAN Set-up 42
- ª Link Set-up 42
- ª Frame Relay 42
- WAN Set-up 43
- Link Set-up 43
- Link Speed 43
- ª WAN Set up 44
- ª Remote Site Set-up 44
- ª Edit Remote Site 44
- Primary Link 48
- Connection Protocol Setting 49
- WAN Set up 51
- Remote Site Set-up 51
- Edit Remote Site 51
- Connection Set-up 51
- Primary Link 51
- Advanced Features 56
- Application Set-up 57
- NAT Exports 58
- NAT Enable 58
- Applications 59
- Security 60
- ª Security Set-up 60
- ª Security Level 60
- Security Parameters 61
- Outgoing User Name 61
- Configure Firewall 62
- 195.100.1.12 63
- 195.100.1.20 63
- Network Address Translation 65
- Enable BACP 66
- Location: Main 67
- SNTP Set-up 69
- Device Set-up 70
- Introduction 71
- Pattern Filtering 72
- Popular Filters 73
- IP Router 74
- Appendix A 75
- Menu Trees 75
- 52P6.06.xxsoftware release: 76
- 52P6.06.xxsoftware release: 77
- Appendix B 78
- Octet Locations on 78
- Ethernet Frames 78
- ETHERNET Type Codes 79
- Octet Locations 80
- Configuration Pages 81
- WARNING ! 82
- Servicing Information 83
- To Clear a “Lost” Password 84
- Remove these screws 85
- Interface 86
- Performing a Software Upgrade 87
- Router A 88
- PC used for 88
- TFTP transfers 88
- Router B 88
- Router C 88
- Appendix D 89
- Interface Pinouts 89
- Switches 90
- Console Pinouts 91
- V.11/X.21 Link Pinouts 93
- DB25 Female DTE 94
- Figure D-7 RS530 Link Pinouts 94
- V.35 Link Pinouts 95
- DB25 MAL 96
- DB25 MALE 96
Manuais e produtos relacionados com Hardware Perle-systems 1700
Hardware Perle-systems 5250 Manual do Utilizador
(4 páginas)
(4 páginas)
Hardware Perle-systems PERLE P850 Manual do Utilizador
(102 páginas)
(102 páginas)
Hardware Perle-systems IOLINK-520 Manual do Utilizador
(110 páginas)
(110 páginas)
Hardware Perle-systems S-110P Manual do Utilizador
(23 páginas)
(23 páginas)
Hardware Perle-systems IOLAN SDS Manual do Utilizador
(162 páginas)
(162 páginas)
Hardware Perle-systems P840 Manual do Utilizador
(58 páginas)
(58 páginas)
Perle Systems Mise en réseau manuels d'utilisation
La liste de Perle Systems Mise en réseau produits contient 11 manuels d'utilisation pour les modèles 10. Tous les guides d'utilisation en format pdf peuvent être téléchargés ou consultés en ligne.
Comentários a estes Manuais